DIY

EAST OAK Smokeless Pan Stove Fire Pit 29"

What’s going on guys? It’s Hai.

It’s still very rainy, wet, and cold here in Washington but I’m currently making plans for a fire pit area on the property. After some research, I’ve decided on the East Oak Pan Stove Fire Pit. This particular one is the Chisel Steel 29” version but there is also a 17” and 21” version. All three sizes are also available in a black finish.

If you don’t hang out outside a lot, this may not be what you’d think a fire pit would look like. You’re probably more familiar with the concrete circle or some other options. But in recent years, these newer stainless steel-style fire pits have really taken off and that’s largely because many will claim to be smokeless.

This is achieved by utilizing a double-walled design with vent holes toward the top of the inner wall. As you burn wood or whatever else, that first burn will cause some smoke to rise but some of it will travel through the gaps between the walls and escape out the small holes. This escaping smoke will get burned again, essentially eliminating it.

However, a key factor in all this is going to be how hot or big the fire is. The fire has to be pretty strong to get that second burn going. A nice thing about the East Oak design is that it features a bunch of oxygen intakes around the entire base and directly under the fire pit. All these intakes should really help to oxygenate the fire and help it get hot enough for that second burn.

That’s a pretty common design for these smokeless fire pits but an annoyance to me is that this design generally does not produce a lot of heat outwards but instead projects it upwards. This means that if you’re standing up and are close to the fire pit, then your upper body will be warm but your lower legs and feet won’t get much. So if you’re sitting down, you’re really only enjoying the ambiance of the fire, not so much the warmth. Some manufacturers have created workarounds for this like Solo Stove and their heat deflector shields but I personally think this is stupid. The heat deflector adds extra bulk, is unsightly, and costs an additional couple hundred bucks on top of an already expensive fire pit.

But times have changed and there are manufacturers claiming to make smokeless fire pits that adequately radiate heat outwards without any add-ons, one of them being East Oak. I don’t particularly understand the science behind it but this is apparently accomplished because the East Oak design features a wider circular base that gets smaller towards the top and the opening turns into a more square shape. Again, I don’t really understand how that works but it supposedly does and I’ll test that out a bit later.

In terms of assembly, this fire pit is pretty much ready to go. You have the main fire pit body, the ashtray that sits inside the fire pit, and the flame ring that sits on top. There really isn’t much to putting this fire pit together.

At this point, I’ve had a chance to use the fire pit and burn wood in it and I want to talk about how that went.

I burned a bundle of wood that I purchased from a local Safeway. It’s been sitting outside under the patio for the last couple of months and was dry. I burned the whole bundle at once just to make things faster. My 29” fire pit not only has a large opening, but it’s also deep. Allowing for a lot of wood to be burned at once. My bundle looked like nothing in there.

In terms of being smokeless, it certainly isn’t smokeless throughout the entire experience. When the fire first starts, there will still be smoke that’s blowing around and that’s not something exclusive to the East Oak but pretty much any fire pit. However, once the wood really started to burn, I did notice that there really was no trace of the smoke. This is the case even though I never witnessed any secondary burn. Maybe I didn’t have enough wood burning? I can’t really say so this will require some more testing.

In terms of East Oak advertising that this fire pit is able to radiate heat sideways, this is a hit or miss depending on how you want to look at it. I personally feel that there was no heat radiating directly to the sides of the fire pit. I can put my hands right up to the sides and basically feel no difference. The metal itself gets quite hot if you try to touch it but it weirdly does not put off any noticeable heat. The chairs that you see in the video above are less than 2 feet away from the fire pit and I was originally worried that they were too close and would get damaged by the heat but that is absolutely not a concern anymore. The chairs stayed chilled the entire time from ambient temperature, never even getting warm. However, if I were to sit at the edge of a chair and my body pokes above the top of the fire pit, then I’d feel A LOT of heat. Being about 2 feet away, the heat is almost unbearable. I would say that standing up and stepping back to 4-5 feet away, I can still feel the warmth on my torso, arms, and head but, again, nothing on my legs. I kind of want to give East Oak the benefit of the doubt and say that this fire pit may radiate more heat if more wood was burned at once, but I feel that I did put in a decent amount. If I had to burn two or three of those bundles at once just to get some lateral heat then this isn’t exactly the most efficient way of keeping warm. Take all that information as you will.

At the end of the day, how do I feel about this East Oak fire pit? As a mostly smokeless fire pit, it gets a pass because it does the job even when the secondary burn didn’t kick in and who knows? When it does things may be even better. As a fire pit that will keep you warm, well that depends on if you want to sit or stand all night. I personally bought this fire pit because it was advertised as being able to radiate heat outwards and in this case, I would say that the East Oak is a total failure. I do not recommend it if you are buying this fire pit to keep yourself warm while sitting down. It just won’t cut it. To me, the question of buying the East Oak all comes down to price. I personally bought it on sale for about $200 and that price for a 29” smokeless fire pit is crazy value. However, when not on sale this fire pit regularly sits around $400-$500. For that price, I would personally not buy this fire pit and just go with a Solo Stove Yukon which is in the same price range but the Solo Stove is better supported in the sense that more companies make accessories for it and you can do more with it.

And that’s going to be it. I’m going to continue and use my East Oak fire pit. I kind of know what it’s capable of now and what I want to use it for so I’m not too disappointed in my purchase.


If you're considering buying any of the products mentioned, please support my work by using the links below.

EAST OAK Fire Pit https://amzn.to/3nR80sj

EAST OAK Pan Stove Fire Pit Cover https://amzn.to/42TxPXc

Solo Stove Yukon 2.0 https://amzn.to/42Pm1FF


Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

or

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

or

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

or

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

CHEAP DIY Floating Shelves

What’s going on guys? It’s Hai.

My office wall has been pretty bare and I’ve been contemplating what to hang on it for a while. I ultimately decided on some floating shelves and I was originally going to buy some but for the size of shelf that I was going for, some of the cost that I saw were ridiculous. So in this blog, I want to share with you how I went about making my own for a very affordable price.

First, let’s start with the wood. I wanted 3 shelves that are 4’ long and 8” wide. From experience, I knew that construction lumber would probably be the cheapest option so I just went to my local Lowe’s. Here, the cheapest option was some 2”x8”x8’ Hemlock for $12.53. This is cheap but was my second choice. I was really going for some 2”x8”x8’ Douglas Fir which would cut the price by more than in half at $4.98 a board. I would need (2) 8’ boards and that would give me (4) 4’ shelves. With Hemlock, that would equate to about $3.13 a shelf but had my Lowe’s had the Douglas Fir in stock, the shelves would’ve only cost about $1.25 a shelf, making it VERY affordable.

Now, I’m no professional woodworker. I just know enough to get things done for my own personal projects. And for this project, I experimented with some stuff that I’ve never used before so I don’t want to give any outright recommendations. I’m just going to show you what I did and give some thoughts.

Again, I wanted (4) 4’ shelves so I ripped the 8’ boards down to size with a miter saw. For this project, I decided to make black shelves because that would best match the color scheme of the room. There’s a variety of ways to make the shelves black but I decided to try MinWax True Black oil-based stain, something I’ve never used before.

In preparation for the stain, I sanded the boards first with 150 grit sandpaper, then 220 grit. This is to get a smoother more presentable finish on the final product and to help the stain soak into the wood. But, I did purposely pick lumber that had more character and imperfections as I was going for a farmhouse aesthetic, so I did try too hard to get a perfect finish.

Once I was happy with the sanding, I moved on to the staining process. To start, I applied a coat of pre-stain. This product helps to distribute the stain more evenly so less blotching occurs with the stain. I have had blotching problems with hemlock in the past so pre-stain is something that I personally now use. The pre-stain itself is very quick and easy to apply. I just used a foam brush to spread it around. The directions say to let it sit for 5-15 minutes, then apply your stain within 2 hours.

Moving on to the actual staining, again, I used Minwax True Black oil-based stain. I’ve been looking for a way to ebonize wood and now that I’ve tried this product, I would say that it’s a very viable option. I don’t know if you can tell, but it comes out jet black like you’re dumping ink on the wood. It may look like much at first but it does thin up a bit when dried and you can still see all the figures in the wood. This is my first time trying this product and I would recommend to not apply a heavy application like I did because it does spread quite well and if you go heavy, this stuff takes a while to dry. It didn’t help that I was doing all this in a cold garage during winter so it took about a day to dry between coats. I did two coats to achieve the look that I wanted so that was two days of just waiting.

Then we move on to applying a finish. I used MinWax polyurethane and the same as before, I just spread it on with a foam brush. Once that’s dried, we can move on to mounting these shelves up.

Now there’s not really much to this step as it really depends on your application and how you want to mount them. I ended up doing three staggered shelves. I went with some brackets that I found on Amazon, which are linked in the description below, and they work just fine but if you go with the same brackets, I would recommend finding your own hardware because the ones that these brackets came with are complete trash. The heads stripped so easily and I had 3 screws that just snapped in half. There are two screws that are broken in my wall where I hit a stud and one that’s lodged at the bottom of a shelf. This shearing happened even with a pilot hole so I would definitely recommend buying your own hardware if possible.

And that’s about it. Some potentially very cheap DIY floating shelves. Depending on the materials that you already have, this project can potentially be very cheap, I mean, like less than $10 if you have the know-how. I bought my brackets because I wanted this look but you can make your own which can bring the cost down even lower. It all depends on what you're going for. Then to spice things up, you can add LED lighting or whatever else to make the shelves really stand out. I’m still working through decorating and what I’m actually using these shelves for so this isn’t finalized.


If you're considering buying any of the products mentioned, please support my work by using the links below.

Floating Shelf Brackets https://amzn.to/3RvUq7X


Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

or

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

or

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

or

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

Kobalt Quiet Tech Air Compressor High Flow Coupler Upgrade

What’s going on guys? It’s Hai.

I recently showcased the Kobalt Quiet Tech Air Compressor that I recently purchased and in this blog, I’m going to show you the first upgrade that I did to it and that’s switching the stock industrial-sized couplers for a high-flow option. The particular couplers that I’ll be using are the Milton HighFlow Pro V Style, part number S-765.

According to Milton’s packaging, this upgrade can provide an airflow increase of up to 70%.

To remove the stock couplers, I’ve found that the easiest way is to just get a wrench in from the bottom and loosen the couplers from there. Lefty loosey, righty tighty. It’s kind of annoying doing this upgrade because there’s little clearance anywhere. You might have the urge to remove the top plate but, just take my word, there are various parts that are screwed to it. You may have more access by removing the plate but then you’ll have parts dangling and I think it would be even more difficult to torque everything down that way. So, just take your time and do a little turn at a time from the bottom.

When you get the coupler out, it’s just a matter of replacing it with the new high-flow coupler. Just remember to use some Teflon tape or other thread sealers to help prevent leaks.

Now, to really maximize airflow gains, you’re going to want to also upgrade your other fittings. I purchased a Milton kit, part number S-217 and it has the various fittings that you’ll need to connect a hose to the air compressor and tools to your hose. Then if you need more male fittings for tool connections, they are readily available online and at a very affordable price.

And that’s about it. This is a very easy install with a lot of potential gains depending on your setup. Not all tools will be able to capitalize on the increased airflow but that’s just how it is. Do your research and figure out if higher-flowing couplers can benefit your setup.


If you're considering buying any of the products mentioned, please support my work by using the links below.

Milton Industries S-765 HI-Flo V-Style Couplers https://amzn.to/3Y4CXWd

Milton S-217 1/4" NPT V Style Coupler and Plug Kit https://amzn.to/3DhjgCr

Milton Industries 760 1/4" MNPT HIGHFLOWPRO™ V-Style Fittings https://amzn.to/3jfc6rJ


Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

or

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

or

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

or

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

DIY 3D Wood Slat Wall Art

What’s going on guys? It’s Hai.

Observant viewers will notice that there is a new addition to the background. This is a 3D wood art piece that I recently made and I’m going to show you guys how I made it.

First, let’s start with wood selection. For my personal build, the foundation was a 2’x4’ sheet of OSB. Because I knew whatever was going to be in the background is going to be visible, I went with OSB because it naturally has that 3D layered look. Now, just a heads up. I purchased a precut 2’x4’ piece but if you want to save money. Definitely buy a regular 4’x8’ sheet because, at the time of this video, that only costs about $11 and the 2’x4’ sheet cost about $19. I was in a rush and haven’t moved my table saw to the new shop yet so I didn’t feel like cutting and really paid the cost. This is definitely not recommended but you do what you gotta do.

Next, we’re going to pick up the wood that makes up the various 3D slats. For this, I personally went with 3 different wood species to give more variation in the final product. If you want something more cohesive in look, maybe buy the same wood for everything.

I personally went with:
(2) 1”x2”x8’ Douglas Fir
(2) 1”x2”x8’ Hemlock
(1) 1”x2”x6’ Poplar
(1) 1”x2”x10’ Poplar

These 6 boards gave me pretty much the exact amount of wood needed for the entire inner 3D pieces.

Next for the frame, I went with (2) 2”x2”x8’ boards of Douglas Fir. This left me with about 3-ish feet of spare material so you can buy less but I knew that I needed the spare just because of how I planned to cut the wood to get certain pieces of the boards.

Other materials needed will include paint, painting supplies, wood strain or finish, wood glue, and various things to use the previously mentioned materials. I’m not getting super-specific right now because you can definitely go with something different and I’ll go over what I used later in this video.

Let’s get started with actually creating this piece. Again, I have a precut 2’x4’ piece of OSB so I didn’t have to cut that down. I actually started with the frame. For this, I went with a pretty straightforward approach by just laying the board over the OSB and marking my corners. I went with an overlapping design that gave me only one exposed wood edge per corner. This takes a few extra cuts but I thought that it would look better.

Next, let’s move on to the inner slats. For this, I started out by doing a rough eyeball estimation of how long I wanted the pieces to be. Remember, there are going to be wood slats coming from both ends so just make sure to leave some empty space in the middle. I was able to pretty quickly figure out what sizes I needed and just started to rip all the boards down with little thought. Remember though, you can take away material but you can’t add it back very easily. So, if you have a bunch of long pieces, you can always cut them down. But if you have a bunch of short pieces, you’re pretty much stuck with them unless you want to try to glue everything back together or buy more wood.

Throughout my cutting process, I would stop and just gauge how much more wood I would need. In the end, it turned out that I needed everything that I purchased. But how many slats are needed is largely going to be determined by how many pieces you’re going to lay on the narrow end. If you have a bunch of vertical pieces, you may need to pick up some more wood.

Once I got everything cut and have an idea of the layout, I moved on to painting. For this, I used an 8-ounce can of Krylon Satin Black paint. I purchased this purely because it was the smallest can and the cheapest paint that I could find. I personally don’t feel that this is the type of piece that I would want to overspend to get good paint because I honestly don’t know how long I’ll keep this thing. You may be different. Just consider what this piece is going to be for. Also, I went with black because it matches the theme of the room and the house. You can definitely go with something different. Now, I will say that with the 8-ounce can, it was pretty much the perfect amount to get everything I needed covered. It was definitely close so don’t go too heavy-handed. Go light and cover everything that you know will be visible, then go back and touch up if needed later.

Now that everything’s painted and dry, we’re going to glue everything down. For my build, I just went pretty quick with the glue. For the frame, I took the time to spread it out to get good coverage but with the slats, I just ran a bead down the center and called it good. This is definitely not the ideal way to apply wood glue but I knew that this piece was going on a wall and no one will be touching it so I wasn’t too worried about my glue job. I knew that it would hold up just fine and it did. In the end, the finished piece is going to be decently heavy and I was able to pick it up by the frame with no problem at all. However, because I purposely chose wood that had a bit more character, one of the frame boards was bowed in one corner. So, I decided to hit it with a brad nail and while I was at it, I did the rest of the perimeter. This was more for cosmetic reasons and had the bow not been there, I wouldn’t have bothered because everything was plenty sturdy with just wood glue.

I do want to mention that I did use some Danish oil to darken some of the slats. This was done to give me some extra variations. I oiled probably less than 10 slats and the rest are just bare wood. You’ll have to use your own judgment and decide if you want to do anything with your project. I left most of the slats unfinished because that’s the look I was going for. For me, this is supposed to be an imperfect piece. There’s wood with knots, dents, cracks, and various other things. I purposefully did as little fixing up as possible because I wanted the imperfections and actually highlighted it by my choice of wood.

Finally, because this piece is heavier than the typical picture frame, I decided to go with a bracket to hang it up. Hillman makes this one. It is 6” long and is rated for 75lbs. This is my first time using this type of hanger but it works a lot like a French cleat if you’re familiar with that. It seems to work just fine and is holding my piece up with no problem.

And that’s about it. This is a fairly simple and straightforward build that most people shouldn’t have any problems finishing. Obviously in this video you saw me using some power tools but this is the type of project that you can get everything done with just hand tools. It’ll be a lot of extra work with cutting especially with all the slats but it can definitely be done.


Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

or

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

or

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

or

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG