Wall Control Metal Pegboard Firearm Wall Mount Panels

November 19, 2022 in Guns & Ammo, Review

What’s going on guys? It’s Hai.

I recently made a video showing the Wall Control panels that I installed in my garage and gym. In short, Wall Control is a metal pegboard option that includes holes for the typical pegboard hooks and also slots to be used with the proprietary Wall Control accessories.

Aside from being used as a way to hang up tools, I have seen Wall Control being shown a lot as a way to display firearms and that’s what I’ve decided to do with the last two panels that I had.

So, here they are. What you’re looking at is two Wall Control 32” x 16” panels, making essentially a 32” x 32” square. Installation of the panels is fairly straightforward, just drill and screw them into the wall.

For size reference, I have up top a CZ Scorpion Evo 3 S1 with an HB Industries 5.3″ Micro K Barrel swap. In the middle is a Century Arms AP5 so essentially a standard length MP5. At the bottom is an AR-15, the Radian Model 1 chambered in 300 Blackout and a 9” barrel. Finally, I have a couple of suppressors hung up, the CGS Mod9 and Dead Air Wolfman.

To hang the firearms up, I’m using the Wall Control 3” U-Shape Slotted hooks. I find that these fit all my firearms from the PCCs to ARs pretty much perfectly. They are just the right size to hold the firearms up straight without them leaning from side to side. I also have the Wall Control 4” U-Shape Slotted hooks but do find these are a bit too big for my firearms. However, if you have a particularly wide stock or forend, you may want to look into the 4” hooks or another option.

One thing that I do recommend is to pick up some rubber hook liners. They help to keep things from sliding around but more importantly to help prevent damage from metal-on-metal contact. Wall Control offers some under the Wall Control branding but it’s about $10 for 3’. That is pretty expensive considering that I paid about $12 for 10’. You may not need that much material and you can buy the liners in shorter lengths, but I’m just saying that there are other options. From the pictures, I can almost assure you that it’s basically the same thing. I’m pretty sure Wall Control just bought the liners in bulk and is reselling them under their own name. I mean at the end of the day, it’s just rubber edge trim, not some special proprietary product.

To hang up my suppressors, I found some pegboard double hooks. They’re rubber coated so should offer protection without needing anything else.

And there you have it, Wall Control panels for use with firearms. I’m pretty happy with the way that these panels turned out but I do want to point out a few things. First, you may have noticed that my setup is a sea of black on black so everything kind of blends in. I kind of knew this going into it. These black panels are spares so I already had them laying around. I didn’t buy them specifically for this project. If I did, I might buy them in a different color and Wall Control does offer them in a wide variety of colors. There are even some companies selling custom-painted panels so look out for that if you don’t want the black-on-black look like I have here. Something else to think about is a lock system if that’s something you care about. You can get some metal tabs that will allow you to lock the trigger guard or whatever else to the Wall Control panels. These aren’t exactly foolproof but do help to slow would-be thieves down a bit.

Overall, I can definitely give this type of setup a recommendation if you’re looking for a way to hang your firearms up on the walls. The panels look pretty clean once you get everything up and I would say I’m happy with everything.

If you're considering buying any of the products mentioned, please support my work by using the links below.

Wall Control Panels https://amzn.to/3NZNoGK

Wall Control U-Hook 3" https://amzn.to/3Esgr2z

Wall Control U-Hook 4" https://amzn.to/3Ack1ey

Wall Control Rubber Hook Liner https://amzn.to/3XqprNl

Pegboard Double Hook https://amzn.to/3XefemJ

Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

Wall Control Metal Pegboard & Accessories

November 12, 2022 in Review

What’s going on guys? It’s Hai.

I previously showcased the Craftsman Versatrack system, a slat board alternative that I installed in my garage. Although this system can be used to organize pretty much anything, I really only use it for yard or outdoor tools. Well, I also needed a way to organize smaller stuff like everyday hand tools. This is where the Wall Control system comes into play.

In short, the Wall Control system is a pegboard alternative. Its biggest selling point is that it’s made out of metal so it should be able to support a lot more weight than your regular masonite wood pegboard. The Wall Control system offers panels in various sizes but the most common are going to be these vertical 32”x16” panels.

Installation of the boards is fairly simple as you essentially just drill and mount them onto a wall. Being that these panels are 16” wide, the idea is that you’ll be able to mount them side by side and get 16” on center. You can of course mount them directly into drywall or any other material, you just have to plan for whatever material it is you have. For my wall, I planned to go into the studs but to get the panels perfectly spaced out, I did end up having to do into drywall. Wall control does provide hardware and wall anchors for this type of situation.

When it comes to actual use, the Wall Control panels do feature holes that should work with any of the regular pegboard accessories. But to maximize the use of this system, you probably want to use the slots that are also on these panels. As far as I know, the slots really only work with the proprietary Wall Control hooks but they do offer a variety of different accessories that should fit most people’s needs. I wasn’t sure what I was going to hang on these panels so I purchased a few Wall Control hooks and a few pegboard hooks from Amazon.

After weeks of playing with these panels, I finally got them dialed in to my liking. Let’s go over some of my attachment accessories so you can get an idea of what’s possible. If you’re interested in any of these, there will be links to everything below.

To hold up my drill and impact driver, I used the Wall Control U-Shape Slotted hooks, 3” hooks in the front and 4” hooks in the back. The screwdriver holder is also from Wall Control. As is the Hammer Handle Bracket. For my wrenches, I started out hanging them up individually with hooks and although I think this aesthetically looks the best, it can take up a lot of space. I ended up using the Olsa Tools magnetic wrench organizers. These are typically used in a metal toolbox but the organizers are magnetic so you can stick them on the Wall Control panels with no problem. I’m also using the Olsa Tools can holder. For size reference, it’s holding a couple of bottles of WD-40 and a cup with various writing instruments. For my paper towel holder, I’m using a pretty simple bent metal wire setup from Amazon. For my hooks, I have a few different options from Wall Control of varying lengths. If you can spring the money for these proprietary hooks, I do think that they provide the best fitment and probably the most strength and durability. That being said, I do have a bunch of various different hooks that I got as a pack from Amazon. For my personal setup, these worked out pretty well.

Also, if your Wall Control panels cover up outlets and you don’t want to lose them, I’ve seen people cut holes into these panels to get access. I thought that that was too much work and ugly so I found a low-profile power strip with a very thin plug that happens to fit under the panels and route out from the bottom.

Overall, I like this Wall Control system. It’s pretty versatile and in my opinion, looks a lot better than the standard masonite pegboard option. Along with this tool wall, I also installed a few panels for the gym and am thinking that I may put up a few panels in my office. The Wall Control system is proving to be very useful in my life and I can definitely give it a recommendation if you’re looking for a way to hang up some of your stuff.

If you're considering buying any of the products mentioned, please support my work by using the links below.

Wall Control Panels https://amzn.to/3NZNoGK

Wall Control U-Hook 3" https://amzn.to/3Esgr2z

Wall Control U-Hook 4" https://amzn.to/3Ack1ey

Wall Control Screwdriver Holder https://amzn.to/3Esdq2h

Wall Control Hammer Handle Bracket https://amzn.to/3Aaeu8k https://amzn.to/3GccPTQ

Olsa Tools Magnetic Wrench Organizer https://amzn.to/3UKex2Q

Olsa Tools Magnetic Can Holder https://amzn.to/3Epubew

Pegboard Paper Towel Holder https://amzn.to/3Epubew

Wall Control Hooks https://amzn.to/3E6kO1O

Pegboard Hooks Variety Pack https://amzn.to/3EamIPg

Pegboard J-Hooks https://amzn.to/3UU4aJN

Thin Power Strip https://amzn.to/3TvcRcf

Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

Craftsman Versatrack

October 28, 2022 in Review

When it comes to organization, one thing that can greatly help is to get your stuff onto the walls. It’s a good amount of space that is typically not utilized. To do this there are a variety of options but we’ll be looking at a slat board alternative, we’ll be looking at Craftsman’s Versatrack system.

The Verstrack itself is a 4’ long x 5.5” wide slat of what seems like a PVC material that has grooves that allow you to hang various accessories that themselves hang your various things.

Installation of the Versatrack can be fairly simple. All it takes is a couple of screws through the Versatrack and into your wall to hold everything up. The tracks even have grooves that indicate where you should mount the hardware. But of course, if you want things to look good and to be secure as possible, you’d probably want to level things out and go into the studs if possible. Craftsman advertises that the Versatrack can support 75lbs per linear foot and although I haven’t even gotten close to that payload, the system definitely seems very robust.

I initially invested in the Versatrack as a way to hang my ladders up on the wall. I started with one 4 foot section and cut it in half to get 2, 2-foot slats on my walls. These slats hold up my ladders just fine, even the Little Giant ladder that weighs about 30 lbs. This is surprising because I was only able to go into one stud on this particular wall and the other side is questionably held in place by a smaller drywall anchor. After seeing how well this side works, I decided to do a larger connected panel. This was a bit more complicated because there was some cutting involved to dodge a circuit breaker cover and an outlet but the project wasn’t too bad.

Cutting the Versatrack is fairly easy. I used a miter saw and it just rips through this material. The cut is very clean and I can’t tell the difference between the cut end and the factory end. I’m sure you can use any other type of saw to get a cut done but if you’re just doing straight cuts on the ends, the miter saw will probably be your best option. Then when it comes time to connect the slats vertically, the pieces have grooves on the top and bottom so everything should line up with no problems.

Throughout this process, I’ve purchased a few different hooks and accessories for the Versatrack. With this, it’s largely trial and error to see what works. Craftsman makes different types of hooks, baskets, shelves, and other accessories for this system. You can even get metal cabinets that’ll directly hand on the Versatrack. This system is quite modular and expandable so it should offer something for most people.

The accessories essentially latch onto the grooves of the slats and hang in place. They have a plastic lever that you can turn to prevent the accessory from coming off the slat but they will still be able to slide left and right.

In terms of cost, the slats themselves are very competitive and among the cheapest option that I’ve found even if you have to provide your own hardware. However, the hooks and accessories are a bit overpriced for what they are. That’s where the price can really add up if you buy a lot and invest in this system.

Overall, I would say that I’m happy with my Versatrack setup. I think it looks good and after some work, I should be able to get a lot of stuff onto the walls. This is definitely a system that I can recommend if you’re looking for a way to organize your space.

If you're considering buying any of the products mentioned, please support my work by using the links below.

Craftsman Versatrack https://amzn.to/3TI20wr

Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

Craftsman 2000 Series 52 in 10 Drawer Cabinet & 8 Drawer Steel Tool Chest

October 20, 2022 in Automotive, Review

I’ve been in the market for a rolling tool cabinet or a combo set like this for a while. I’ve always liked the Craftsman toolbox look so when it came time to buy, the 2000 Series was something that I looked at a lot. It doesn’t help that I shop at Lowe’s a lot so I saw them all the time.

In terms of basic specs, these boxes are constructed from 18-20 gauge steel and feature drawers that support 100 lbs of product. The drawers themselves feature soft close hinges and are lockable. The cabinet also features four wheels, two of which turn and are lockable. Both the cabinet and tool chest feature side handles. The cabinet has one handle and is not switchable from side to side. The tool chest has a handle on both sides that telescopes in and out. Both pieces should come with liners for all the drawers and top surfaces, along with two keys per lock. I say should because I was missing a liner and a key. Both of which I was able to get by reaching out to Craftsman’s customer service.

So I’ve had this combo set for a few weeks now and use it essentially every day. I don’t have all my tools moved in yet but can provide some opinions. First off let’s talk about the price. The cabinet retails for $629 but I’ve always seen it at $539. The tool chest retails at $499 but I’ve always seen it for $409. Together, you’re looking at $1128 MSRP but it’s realistically $948. In my opinion, I think that may be overpriced. This is going to be a more subjective take but I think for the money, there are better options in the market. Prior to buying, I was pretty set on this Craftsman set because I’ve always wanted a Craftsman toolbox. However, after walking into a Home Depot one day and seeing the options there, I really questioned the Craftsman. The two most common toolbox brands that you’ll see at Home Depot will probably be Milwaukee and Husky. The Milwaukee options, in my opinion, are going to be the best among the three but they cost the most. For my needs, I didn’t think the cost of the Milwaukee would’ve been justifiable. Husky, on the other hand, being Home Depot’s house brand, the prices are a bit lower and closer in cost to the Craftsman. So for me, it was between Craftsman and Husky. After a few days of going back and forth between stores and looking at the various options, I actually decided to buy a Husky combo set. The fit and finish just felt better. The liners were the higher quality kind, not the cheap perforated stuff as with the Craftsman. The Husky has plastic end caps on all the ends of the drawers. The Craftsman does not and the exposed metal edges aren’t rounded off or smooth. They can definitely cut you if you scrape them with a bit of force. But again, those are just my personal feelings.

So, why did I buy this Craftsman set? Long story short, I was able to get this particular set for 40% off. So at the price that I paid, it was a no-brainer to go with the Craftsman. My situation is pretty unique. Most people are not going to have the same opportunity so for the most part, I would definitely recommend visiting a local Lowe’s if possible to check the Craftsman box out for yourself. Then find another retailer, like Home Depot, that has some competitor options and get a feel for those. Specs written online are great but you definitely can feel the difference in quality between boxes just by playing with them for a few minutes.

Personally, if I was paying retail or even the normal sale price, I wouldn’t buy the Craftsman and get a Husky. The Husky options actually go on sale quite often and when they do, they are actually a better deal in terms of cost. Then if I wanted a little more quality and can spend some more money, I’d go Milwaukee.

Overall, I think these Craftsman 2000 Series boxes are fine. They do the job and serve their purpose but I do think that there are better options for the price. Again, I would highly recommend you check various options out in person.

Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG

Rubbermaid Roughneck Resin Storage Shed 5-ft x 4-ft

September 26, 2022 in Review

I recently moved into a new home and was in need for a shed. I needed one quick and from what I’ve seen, in the shed world, nothing’s faster when it comes to DIY than a resin shed. Everything’s pre-made and all you have to do is put it together. In terms of sheds, I don’t know how it could be any easier aside from buying a pre-assembled one and having it delivered to your property.

I personally purchased a 5-ft x 4-ft Rubbermaid Roughneck Resin Storage Shed and was able to assemble it by myself. So assumably, anything smaller should also be easily assembled by one person but having help will definitely move things along. Assembling the Rubbermaid shed is largely just punching out some plastic for the screws and then screwing everything together. All the screws are the same size and you can pretty much get everything done with just a drill, drill bit, and a Phillips screwdriver. The entire thing is like a giant jigsaw puzzle but one of those extremely simple ones with like 50 pieces. I don’t think putting this shed together should be any problem for someone with the most basic ability to read instructions and comprehend. Again, I put the shed together by myself and even moved it by myself with a single hand truck but if you have some help it just makes an already easy project that much easier.

Now, like all sheds, you have some options when it comes to the base. You can build something but because the Rubbermaid shed comes with a floor, you can get away with direct ground contact in some situations. I planned to put the shed in this rocky section of the property and it largely worked until I put the doors on the shed. What I found was that if there’s a big enough elevation shift from one side to the other, the doors won’t work properly. In my case, the rocks made the right side of the shed slightly higher than the left and this caused the left door to pop completely off when both doors are closed. I could’ve resolved this by leveling out the ground by various means but I took the easiest route and just threw a sheet of pressure treated plywood under the shed. This gave my shed a flat enough base for the doors to work and some protection from the rocks.

So, at the end of the day, what do I think about this Rubbermaid resin shed? To be honest and knowing what I know now, I would buy something different or if I had the time, I would just build my own shed from wood. This Rubbermaid shed just feels like a child’s toy. The walls are pretty thin and flex with little force. If someone wanted to and had a knife, even a pocket knife, I think they’d be able to cut through the walls relatively easily. But in reality, that’s not needed at all because the doors are barely held in place. When I lock the doors together and give them a little tug, there is a lot of movement. That’s a gap of a couple of inches and I’m telling you now as someone who’s been playing with these doors a lot over the past few days, that gap allows me to leverage so much energy that not that much force is needed to rip these doors off from the shed because it’s not like there solidly held in place by anything. It’s just a piece of plastic going into a groove at the top and bottom. This is a huge problem and such a security risk to me. This is a deal breaker and I personally would say that it makes this Rubbermaid Roughneck Resin Storage Shed not worth it. It’s fine if you’re storing stuff that you really don’t care about but if you’re looking for something with a reasonable amount of security, this is not it. Look at one of those cheap sheet metal sheds if you’re looking for something relatively easy to put together and possibly even cheaper. I’m pretty disappointed in this purchase but it is what it is.

If you're considering buying any of the products mentioned, please support my work by using the links below.

Rubbermaid 5'x4' Shed https://amzn.to/3eZ7C6a

Want to support my work?

Consider visiting the shop and buying "Absolutely Nothing"
https://www.HaiHoangTran.com/shop/absolutely-nothing

Become a YouTube member!

https://www.youtube.com/channel/UCLUO-2ltlWfydRZ7pRRnXkw/join

Become a Patron!
https://www.patreon.com/HaiHoangTran

Buy some official merch!
https://www.youtube.com/haitran/store

PayPal
https://www.PayPal.me/HaiHoangTran

Just shop on Amazon via this link!
https://amzn.to/2FgsDnG